Stm32f10x

[muhittin_kaplan]

buldum.

bunu ben print edip kitap heline getirdim.
http://www6.in.tum.de/pub/Main/TeachingWs2012Echtzeitsysteme/stm32f_firmw.pdf

[yldzelektronik]

GPIO ları anladım gibi.Önce bağlı olduğu bus için clock erişimini sağlıyoruz sonra mod ile giriş çıkış durumlarını belirleyip erişim sağlıyoruz.Tek seferde erişimin olması ne güzel.Gerçi tam bilmiyorum ama picdeki gibi mi acaba?Önce bank bişeye geç sonra pini yönlendir.Sonra yine önceki banka geç falan gibi?

Benim anlamakta sıkıntı yaşadığım kısım alternate function kısımı.Bir pin hem gpio, hem fsmc d0 hem sdio d2 (farazi örnek.Böyle olmasa da bazı pinlerde 3 tane remap ile erişilebilecek donanımlar var).Bunları nasıl hallediyoruz.Sanırım şöyle;

Önce gpio gibi düşünüp portu hangi busu bağlıysa clocklandırıyoruz.Sonra alternate function olduğunu belirtiyoruz.Sonra da hangi donanım ise (yukarıdaki örnek için fmsc) onun enable mi ediyoruz clock mu veriyoruz?Nasıl yapılıyor?Burada işte kafam karışıyor biraz.

Bir de bu pinin 3. durumu var (yine yukarıdaki örnek için fsmc değil sdio olması).

[MC_Skywalker]

mcu üreticisine göre işlem biraz değişiyor ama dediğin gibi;
clock uygula portu aktif et, pinin durumunu belirle
Pin doğrudan ram da bir bölge okur yazar gibi adresine erişip işlem yapabilirsin.

Ek:
örn

void PortF_Init(void)                   //TivaC nin port F ilk kurulumu (initializing)
{ 
  volatile unsigned long delay;
        SYSCTL_RCGC2_R |= 0x00000020; 	// 1) Port F'in clock aktif et
	delay = SYSCTL_RCGC2_R; 	// clock için bir müddeet bekle
	GPIO_PORTF_LOCK_R = 0x4C4F434B; // 2) Port F'in GPIO aç
	GPIO_PORTF_CR_R = 0x1F; 	//  PF4-0 ilk 5 bit te değişikliğe izinver
                                        //
	GPIO_PORTF_AMSEL_R = 0x00; 	// 3) Port F Analog özelliği kullanılmayacak
	GPIO_PORTF_PCTL_R = 0x00000000; // 4) PCTL GPIO on PF4-0
	GPIO_PORTF_DIR_R = 0x0E; 	// 5) PF4,PF0 girş, PF3-1 çıkış
	GPIO_PORTF_AFSEL_R = 0x00; 	// 6) PF7-0 portun alternatif fonksiyonlarını kapat
	GPIO_PORTF_PUR_R = 0x11; 	// PF0 ve PF4 için zayıf iç pull-up devreye al
	GPIO_PORTF_DEN_R = 0x1F; 	// 7) PF4-0 Dijital girşi çıkış aktif et.
//	GPIO_PORTF_DATA_R = 0x00;       // Port F kaydedicisine 0x00 değeri init işleminden sonra yükle
}

[AsHeS]

Kütüphaneden ezberlemeye çalışacağınıza datasheetten bakıp yazmak çok daha hızlı ve de init prosedürleri adım adım anlatılıyor genelde. Bana kullanması daha kolay geliyor açıkçası kütüphanede neyi hangi sırada yapacaksınız meçhul. Zaten buna sarf edeceğim eforu datasheetin yapılanmasını anlamaya ayırmakla çok mantıklı bir iş yaptığımı da ekstra olarak düşünmekteyim. Ha hiç mi geçmeyi düşünmüyorum kütüphanelere evet geçicem fakat kolay olduğu için değil alt katmanda düzeni sağlamak için.

[CoşkuN]

"Karşıt görüşlü "kütüphaneciler" ve "registercılar" grupları arasında çıkan kavgada 3 kişi yaralandı" haberleri görür müyüz 

Register'ları anlamak bence de çok faydalı başlangıçta, ama bir süre sonra işkenceye de dönebiliyor. Kütüphaneler de zaten rahatlığı sağlamak için var. Ezberleme diye birşey zaten geçerli değil. Bu işler ezber kabul etmiyor pek.

[AsHeS]

"Karşıt görüşlü "kütüphaneciler" ve "registercılar" grupları arasında çıkan kavgada 3 kişi yaralandı" haberleri görür müyüz 

Hocam yukarıda da dediğim gibi kütüphane bana açıkçası zul geliyor ama kodda standartlaşmak için kullanılması iyi olur.

[Gökhan BEKEN]

Ben de bunları buldum:

(yukarıdakinin aynısı)STM32F101xx and STM32F103xx:
https://my.st.com/public/STe2ecommunities/mcu/Lists/cortex_mx_stm32/Attachments/25258/UM0427%20USER%20MANUAL.pdf

STM32F2xx Standard Peripheral Library:
http://www.st.com/st-web-ui/static/active/en/resource/technical/document/user_manual/DM00023896.pdf

[yldzelektronik]

Merabalar,

Bu system_init olayı çok kafa karıştırıcı bir hal aldı.Normal şartlarda ben systeminit tanımlamadığımda startup dosyasında gösterilen yere gitmesi gerek miyor mı?Veya ben startup dosyasında gösterilen yere gitmesini nasıl önleyebilirim?Nasıl kendi osc rutinlerimi hazırlayabilirim?

[Mucit23]

Normalde Reset vektöründen sonra program ilk olarak system init fonksiyonunu işler sonrasında main'e düşer.
Sende main içerisinde system init fonksiyonunu çağırabilirsin.

[muhittin_kaplan]

Hocam mobilden yaziyorum, benim blogda f10x ile alakali yazilarda kendi clock ayarlarim mevcut alla system init fonksiyonuna ihtiyaciniz yok

[yldzelektronik]

Başlık stm32f10x ancak stm32f407 ile uğraşıyorum.

Clock config tool exceli ile clock ayarlarını yapıp external seçmeme rağmen hep internal seçiyo ve bir türlü 168mhz de koşturamadım.Bülent abinin systeminit fonksiyonu ile yapabiliyorum ancak.O toolun system initi şöyle;

/**
  ******************************************************************************
  * @file    system_stm32f4xx.c
  * @author  MCD Application Team
  * @version V1.0.1
  * @date    24-June-2014
  * @brief   CMSIS Cortex-M4 Device Peripheral Access Layer System Source File.
  *          This file contains the system clock configuration for STM32F4xx devices,
  *          and is generated by the clock configuration tool
  *          stm32f4xx_Clock_Configuration_V1.0.1.xls
  *             
  * 1.  This file provides two functions and one global variable to be called from 
  *     user application:
  *      - SystemInit(): Setups the system clock (System clock source, PLL Multiplier
  *                      and Divider factors, AHB/APBx prescalers and Flash settings),
  *                      depending on the configuration made in the clock xls tool. 
  *                      This function is called at startup just after reset and 
  *                      before branch to main program. This call is made inside
  *                      the "startup_stm32f4xx.s" file.
  *
  *      - SystemCoreClock variable: Contains the core clock (HCLK), it can be used
  *                                  by the user application to setup the SysTick 
  *                                  timer or configure other parameters.
  *                                     
  *      - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must
  *                                 be called whenever the core clock is changed
  *                                 during program execution.
  *
  * 2. After each device reset the HSI (16 MHz) is used as system clock source.
  *    Then SystemInit() function is called, in "startup_stm32f4xx.s" file, to
  *    configure the system clock before to branch to main program.
  *
  * 3. If the system clock source selected by user fails to startup, the SystemInit()
  *    function will do nothing and HSI still used as system clock source. User can 
  *    add some code to deal with this issue inside the SetSysClock() function.
  *
  * 4. The default value of HSE crystal is set to 25MHz, refer to "HSE_VALUE" define
  *    in "stm32f4xx.h" file. When HSE is used as system clock source, directly or
  *    through PLL, and you are using different crystal you have to adapt the HSE
  *    value to your own configuration.
  *
  * 5. This file configures the system clock as follows:
  *=============================================================================
  *=============================================================================
  *        Supported STM32F4xx device revision    | Rev A
  *-----------------------------------------------------------------------------
  *        System Clock source                    | PLL (HSE)
  *-----------------------------------------------------------------------------
  *        SYSCLK(Hz)                             | 168000000
  *-----------------------------------------------------------------------------
  *        HCLK(Hz)                               | 168000000
  *-----------------------------------------------------------------------------
  *        AHB Prescaler                          | 1
  *-----------------------------------------------------------------------------
  *        APB1 Prescaler                         | 4
  *-----------------------------------------------------------------------------
  *        APB2 Prescaler                         | 2
  *-----------------------------------------------------------------------------
  *        HSE Frequency(Hz)                      | 8000000
  *-----------------------------------------------------------------------------
  *        PLL_M                                  | 8
  *-----------------------------------------------------------------------------
  *        PLL_N                                  | 336
  *-----------------------------------------------------------------------------
  *        PLL_P                                  | 2
  *-----------------------------------------------------------------------------
  *        PLL_Q                                  | 7
  *-----------------------------------------------------------------------------
  *        PLLI2S_N                               | NA
  *-----------------------------------------------------------------------------
  *        PLLI2S_R                               | NA
  *-----------------------------------------------------------------------------
  *        I2S input clock                        | NA
  *-----------------------------------------------------------------------------
  *        VDD(V)                                 | 3,3
  *-----------------------------------------------------------------------------
  *        Main regulator output voltage          | Scale1 mode
  *-----------------------------------------------------------------------------
  *        Flash Latency(WS)                      | 5
  *-----------------------------------------------------------------------------
  *        Prefetch Buffer                        | OFF
  *-----------------------------------------------------------------------------
  *        Instruction cache                      | ON
  *-----------------------------------------------------------------------------
  *        Data cache                             | ON
  *-----------------------------------------------------------------------------
  *=============================================================================
  ****************************************************************************** 
  * @attention
  *
  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
  * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
  *
  * <h2><center>&copy; COPYRIGHT 2011 STMicroelectronics</center></h2>
  ******************************************************************************
  */

/** @addtogroup CMSIS
  * @{
  */

/** @addtogroup stm32f4xx_system
  * @{
  */  
  
/** @addtogroup STM32F4xx_System_Private_Includes
  * @{
  */

#include "stm32f4xx.h"

/**
  * @}
  */

/** @addtogroup STM32F4xx_System_Private_TypesDefinitions
  * @{
  */

/**
  * @}
  */

/** @addtogroup STM32F4xx_System_Private_Defines
  * @{
  */

/************************* Miscellaneous Configuration ************************/
/*!< Uncomment the following line if you need to use external SRAM mounted
     on STM324xG_EVAL board as data memory  */
/* #define DATA_IN_ExtSRAM */

/*!< Uncomment the following line if you need to relocate your vector Table in
     Internal SRAM. */
/* #define VECT_TAB_SRAM */
#define VECT_TAB_OFFSET  0x00 /*!< Vector Table base offset field. 
                                   This value must be a multiple of 0x200. */
/******************************************************************************/

/************************* PLL Parameters *************************************/
/* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N */
#define PLL_M      8
#define PLL_N      336

/* SYSCLK = PLL_VCO / PLL_P */
#define PLL_P      2

/* USB OTG FS, SDIO and RNG Clock =  PLL_VCO / PLLQ */
#define PLL_Q      7

/******************************************************************************/

/**
  * @}
  */

/** @addtogroup STM32F4xx_System_Private_Macros
  * @{
  */

/**
  * @}
  */

/** @addtogroup STM32F4xx_System_Private_Variables
  * @{
  */

  uint32_t SystemCoreClock = 168000000;

  __I uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9};

/**
  * @}
  */

/** @addtogroup STM32F4xx_System_Private_FunctionPrototypes
  * @{
  */

static void SetSysClock(void);
#ifdef DATA_IN_ExtSRAM
  static void SystemInit_ExtMemCtl(void); 
#endif /* DATA_IN_ExtSRAM */

/**
  * @}
  */

/** @addtogroup STM32F4xx_System_Private_Functions
  * @{
  */

/**
  * @brief  Setup the microcontroller system
  *         Initialize the Embedded Flash Interface, the PLL and update the 
  *         SystemFrequency variable.
  * @param  None
  * @retval None
  */
void SystemInit(void)
{
  /* FPU settings ------------------------------------------------------------*/
  #if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
    SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2));  /* set CP10 and CP11 Full Access */
  #endif
  /* Reset the RCC clock configuration to the default reset state ------------*/
  /* Set HSION bit */
  RCC->CR |= (uint32_t)0x00000001;

  /* Reset CFGR register */
  RCC->CFGR = 0x00000000;

  /* Reset HSEON, CSSON and PLLON bits */
  RCC->CR &= (uint32_t)0xFEF6FFFF;

  /* Reset PLLCFGR register */
  RCC->PLLCFGR = 0x24003010;

  /* Reset HSEBYP bit */
  RCC->CR &= (uint32_t)0xFFFBFFFF;

  /* Disable all interrupts */
  RCC->CIR = 0x00000000;

#ifdef DATA_IN_ExtSRAM
  SystemInit_ExtMemCtl(); 
#endif /* DATA_IN_ExtSRAM */
         
  /* Configure the System clock source, PLL Multiplier and Divider factors, 
     AHB/APBx prescalers and Flash settings ----------------------------------*/
  SetSysClock();

  /* Configure the Vector Table location add offset address ------------------*/
#ifdef VECT_TAB_SRAM
  SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
#else
  SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
#endif
}

/**
   * @brief  Update SystemCoreClock variable according to Clock Register Values.
  *         The SystemCoreClock variable contains the core clock (HCLK), it can
  *         be used by the user application to setup the SysTick timer or configure
  *         other parameters.
  *           
  * @note   Each time the core clock (HCLK) changes, this function must be called
  *         to update SystemCoreClock variable value. Otherwise, any configuration
  *         based on this variable will be incorrect.         
  *     
  * @note   - The system frequency computed by this function is not the real 
  *           frequency in the chip. It is calculated based on the predefined 
  *           constant and the selected clock source:
  *             
  *           - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*)
  *                                              
  *           - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**)
  *                          
  *           - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**) 
  *             or HSI_VALUE(*) multiplied/divided by the PLL factors.
  *         
  *         (*) HSI_VALUE is a constant defined in stm32f4xx.h file (default value
  *             16 MHz) but the real value may vary depending on the variations
  *             in voltage and temperature.   
  *    
  *         (**) HSE_VALUE is a constant defined in stm32f4xx.h file (default value
  *              25 MHz), user has to ensure that HSE_VALUE is same as the real
  *              frequency of the crystal used. Otherwise, this function may
  *              have wrong result.
  *                
  *         - The result of this function could be not correct when using fractional
  *           value for HSE crystal.
  *     
  * @param  None
  * @retval None
  */
void SystemCoreClockUpdate(void)
{
  uint32_t tmp = 0, pllvco = 0, pllp = 2, pllsource = 0, pllm = 2;
  
  /* Get SYSCLK source -------------------------------------------------------*/
  tmp = RCC->CFGR & RCC_CFGR_SWS;

  switch (tmp)
  {
    case 0x00:  /* HSI used as system clock source */
      SystemCoreClock = HSI_VALUE;
      break;
    case 0x04:  /* HSE used as system clock source */
      SystemCoreClock = HSE_VALUE;
      break;
    case 0x08:  /* PLL used as system clock source */

      /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N
         SYSCLK = PLL_VCO / PLL_P
         */    
      pllsource = (RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) >> 22;
      pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM;
      
      if (pllsource != 0)
      {
        /* HSE used as PLL clock source */
        pllvco = (HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
      }
      else
      {
        /* HSI used as PLL clock source */
        pllvco = (HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);      
      }

      pllp = (((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >>16) + 1 ) *2;
      SystemCoreClock = pllvco/pllp;
      break;
    default:
      SystemCoreClock = HSI_VALUE;
      break;
  }
  /* Compute HCLK frequency --------------------------------------------------*/
  /* Get HCLK prescaler */
  tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)];
  /* HCLK frequency */
  SystemCoreClock >>= tmp;
}

/**
  * @brief  Configures the System clock source, PLL Multiplier and Divider factors, 
  *         AHB/APBx prescalers and Flash settings
  * @Note   This function should be called only once the RCC clock configuration  
  *         is reset to the default reset state (done in SystemInit() function).   
  * @param  None
  * @retval None
  */
static void SetSysClock(void)
{
/******************************************************************************/
/*            PLL (clocked by HSE) used as System clock source                */
/******************************************************************************/
  __IO uint32_t StartUpCounter = 0, HSEStatus = 0;
  
  /* Enable HSE */
  RCC->CR |= ((uint32_t)RCC_CR_HSEON);
 
  /* Wait till HSE is ready and if Time out is reached exit */
  do
  {
    HSEStatus = RCC->CR & RCC_CR_HSERDY;
    StartUpCounter++;
  } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT));

  if ((RCC->CR & RCC_CR_HSERDY) != RESET)
  {
    HSEStatus = (uint32_t)0x01;
  }
  else
  {
    HSEStatus = (uint32_t)0x00;
  }

  if (HSEStatus == (uint32_t)0x01)
  {
    /* Select regulator voltage output Scale 1 mode, System frequency up to 168 MHz */
    RCC->APB1ENR |= RCC_APB1ENR_PWREN;
    PWR->CR |= PWR_CR_VOS;

    /* HCLK = SYSCLK / 1*/
    RCC->CFGR |= RCC_CFGR_HPRE_DIV1;
      
    /* PCLK2 = HCLK / 2*/
    RCC->CFGR |= RCC_CFGR_PPRE2_DIV2;
    
    /* PCLK1 = HCLK / 4*/
    RCC->CFGR |= RCC_CFGR_PPRE1_DIV4;

    /* Configure the main PLL */
    RCC->PLLCFGR = PLL_M | (PLL_N << 6) | (((PLL_P >> 1) -1) << 16) |
                   (RCC_PLLCFGR_PLLSRC_HSE) | (PLL_Q << 24);

    /* Enable the main PLL */
    RCC->CR |= RCC_CR_PLLON;

    /* Wait till the main PLL is ready */
    while((RCC->CR & RCC_CR_PLLRDY) == 0)
    {
    }
   
    /* Configure Flash prefetch, Instruction cache, Data cache and wait state */
    FLASH->ACR = FLASH_ACR_ICEN |FLASH_ACR_DCEN |FLASH_ACR_LATENCY_5WS;

    /* Select the main PLL as system clock source */
    RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW));
    RCC->CFGR |= RCC_CFGR_SW_PLL;

    /* Wait till the main PLL is used as system clock source */
    while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS ) != RCC_CFGR_SWS_PLL);
    {
    }
  }
  else
  { /* If HSE fails to start-up, the application will have wrong clock
         configuration. User can add here some code to deal with this error */
  }

}

/**
  * @brief  Setup the external memory controller. Called in startup_stm32f4xx.s 
  *          before jump to __main
  * @param  None
  * @retval None
  */ 
#ifdef DATA_IN_ExtSRAM
/**
  * @brief  Setup the external memory controller.
  *         Called in startup_stm32f4xx.s before jump to main.
  *         This function configures the external SRAM mounted on STM324xG_EVAL board
  *         This SRAM will be used as program data memory (including heap and stack).
  * @param  None
  * @retval None
  */
void SystemInit_ExtMemCtl(void)
{
/*-- GPIOs Configuration -----------------------------------------------------*/
/*
 +-------------------+--------------------+------------------+------------------+
 +                       SRAM pins assignment                                   +
 +-------------------+--------------------+------------------+------------------+
 | PD0  <-> FSMC_D2  | PE0  <-> FSMC_NBL0 | PF0  <-> FSMC_A0 | PG0 <-> FSMC_A10 | 
 | PD1  <-> FSMC_D3  | PE1  <-> FSMC_NBL1 | PF1  <-> FSMC_A1 | PG1 <-> FSMC_A11 | 
 | PD4  <-> FSMC_NOE | PE3  <-> FSMC_A19  | PF2  <-> FSMC_A2 | PG2 <-> FSMC_A12 | 
 | PD5  <-> FSMC_NWE | PE4  <-> FSMC_A20  | PF3  <-> FSMC_A3 | PG3 <-> FSMC_A13 | 
 | PD8  <-> FSMC_D13 | PE7  <-> FSMC_D4   | PF4  <-> FSMC_A4 | PG4 <-> FSMC_A14 | 
 | PD9  <-> FSMC_D14 | PE8  <-> FSMC_D5   | PF5  <-> FSMC_A5 | PG5 <-> FSMC_A15 | 
 | PD10 <-> FSMC_D15 | PE9  <-> FSMC_D6   | PF12 <-> FSMC_A6 | PG9 <-> FSMC_NE2 | 
 | PD11 <-> FSMC_A16 | PE10 <-> FSMC_D7   | PF13 <-> FSMC_A7 |------------------+
 | PD12 <-> FSMC_A17 | PE11 <-> FSMC_D8   | PF14 <-> FSMC_A8 | 
 | PD13 <-> FSMC_A18 | PE12 <-> FSMC_D9   | PF15 <-> FSMC_A9 | 
 | PD14 <-> FSMC_D0  | PE13 <-> FSMC_D10  |------------------+
 | PD15 <-> FSMC_D1  | PE14 <-> FSMC_D11  |
 |                   | PE15 <-> FSMC_D12  |
 +-------------------+--------------------+
*/
   /* Enable GPIOD, GPIOE, GPIOF and GPIOG interface clock */
  RCC->AHB1ENR   = 0x00000078;
  
  /* Connect PDx pins to FSMC Alternate function */
  GPIOD->AFR[0]  = 0x00cc00cc;
  GPIOD->AFR[1]  = 0xcc0ccccc;
  /* Configure PDx pins in Alternate function mode */  
  GPIOD->MODER   = 0xaaaa0a0a;
  /* Configure PDx pins speed to 100 MHz */  
  GPIOD->OSPEEDR = 0xffff0f0f;
  /* Configure PDx pins Output type to push-pull */  
  GPIOD->OTYPER  = 0x00000000;
  /* No pull-up, pull-down for PDx pins */ 
  GPIOD->PUPDR   = 0x00000000;

  /* Connect PEx pins to FSMC Alternate function */
  GPIOE->AFR[0]  = 0xc00cc0cc;
  GPIOE->AFR[1]  = 0xcccccccc;
  /* Configure PEx pins in Alternate function mode */ 
  GPIOE->MODER   = 0xaaaa828a;
  /* Configure PEx pins speed to 100 MHz */ 
  GPIOE->OSPEEDR = 0xffffc3cf;
  /* Configure PEx pins Output type to push-pull */  
  GPIOE->OTYPER  = 0x00000000;
  /* No pull-up, pull-down for PEx pins */ 
  GPIOE->PUPDR   = 0x00000000;

  /* Connect PFx pins to FSMC Alternate function */
  GPIOF->AFR[0]  = 0x00cccccc;
  GPIOF->AFR[1]  = 0xcccc0000;
  /* Configure PFx pins in Alternate function mode */   
  GPIOF->MODER   = 0xaa000aaa;
  /* Configure PFx pins speed to 100 MHz */ 
  GPIOF->OSPEEDR = 0xff000fff;
  /* Configure PFx pins Output type to push-pull */  
  GPIOF->OTYPER  = 0x00000000;
  /* No pull-up, pull-down for PFx pins */ 
  GPIOF->PUPDR   = 0x00000000;

  /* Connect PGx pins to FSMC Alternate function */
  GPIOG->AFR[0]  = 0x00cccccc;
  GPIOG->AFR[1]  = 0x000000c0;
  /* Configure PGx pins in Alternate function mode */ 
  GPIOG->MODER   = 0x00080aaa;
  /* Configure PGx pins speed to 100 MHz */ 
  GPIOG->OSPEEDR = 0x000c0fff;
  /* Configure PGx pins Output type to push-pull */  
  GPIOG->OTYPER  = 0x00000000;
  /* No pull-up, pull-down for PGx pins */ 
  GPIOG->PUPDR   = 0x00000000;
  
/*-- FSMC Configuration ------------------------------------------------------*/
  /* Enable the FSMC interface clock */
  RCC->AHB3ENR         = 0x00000001;

  /* Configure and enable Bank1_SRAM2 */
  FSMC_Bank1->BTCR[2]  = 0x00001015;
  FSMC_Bank1->BTCR[3]  = 0x00010603;
  FSMC_Bank1E->BWTR[2] = 0x0fffffff;
 /*
  Bank1_SRAM2 is configured as follow:

  p.FSMC_AddressSetupTime = 3;
  p.FSMC_AddressHoldTime = 0;
  p.FSMC_DataSetupTime = 6;
  p.FSMC_BusTurnAroundDuration = 1;
  p.FSMC_CLKDivision = 0;
  p.FSMC_DataLatency = 0;
  p.FSMC_AccessMode = FSMC_AccessMode_A;

  FSMC_NORSRAMInitStructure.FSMC_Bank = FSMC_Bank1_NORSRAM2;
  FSMC_NORSRAMInitStructure.FSMC_DataAddressMux = FSMC_DataAddressMux_Disable;
  FSMC_NORSRAMInitStructure.FSMC_MemoryType = FSMC_MemoryType_PSRAM;
  FSMC_NORSRAMInitStructure.FSMC_MemoryDataWidth = FSMC_MemoryDataWidth_16b;
  FSMC_NORSRAMInitStructure.FSMC_BurstAccessMode = FSMC_BurstAccessMode_Disable;
  FSMC_NORSRAMInitStructure.FSMC_AsynchronousWait = FSMC_AsynchronousWait_Disable;  
  FSMC_NORSRAMInitStructure.FSMC_WaitSignalPolarity = FSMC_WaitSignalPolarity_Low;
  FSMC_NORSRAMInitStructure.FSMC_WrapMode = FSMC_WrapMode_Disable;
  FSMC_NORSRAMInitStructure.FSMC_WaitSignalActive = FSMC_WaitSignalActive_BeforeWaitState;
  FSMC_NORSRAMInitStructure.FSMC_WriteOperation = FSMC_WriteOperation_Enable;
  FSMC_NORSRAMInitStructure.FSMC_WaitSignal = FSMC_WaitSignal_Disable;
  FSMC_NORSRAMInitStructure.FSMC_ExtendedMode = FSMC_ExtendedMode_Disable;
  FSMC_NORSRAMInitStructure.FSMC_WriteBurst = FSMC_WriteBurst_Disable;
  FSMC_NORSRAMInitStructure.FSMC_ReadWriteTimingStruct = &p;
  FSMC_NORSRAMInitStructure.FSMC_WriteTimingStruct = &p;
*/  
}
#endif /* DATA_IN_ExtSRAM */


/**
  * @}
  */

/**
  * @}
  */
  
/**
  * @}
  */    
/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/

[muhittin_kaplan]

tamam hocam siz ne yapmak istiyorsunuz, bu dosyayı ekleyip systeminit çağıracaksınız

[yldzelektronik]

İşlemciyi bir türlü 168mhzde koşturamadım.Çıldırtacak yahu.168mhz de koşan programı inceliyorum noktasına kadar aynı.Ama olmuyor.Benim programım 168mhzde koşmuyor.

Clock Config Tool ile yapıyorum birde.Sorun nedir ki?Denemelerimi Stm32f4 disco ile yapıyorum.

[muhittin_kaplan]

Derleyicin nedir

[yldzelektronik]

Gcc arm. Ide emblocks